大家都搜：
位置信号
1、signal───adj.显著的；作为信号的；n.(Signal)人名；(瑞典)西格纳尔；vt.标志；用信号通知；表示；n.信号；暗号；导火线；vi.发信号
2、home signal───进站信号（机）；[铁路]进站信号；[铁路]进站信号机
3、digital signal───[自][通信]数字信号
4、radio signal───无线电讯号；无线电信号
5、signal processing───[通信]信号处理
6、position───v.安置；把……放在适当位置；n.位置；姿态；处境，地位；观点；职位，工作；站位
7、signal wire───[通信]信号线
8、alarm signal───[安全]警报信号；n.警报，警报信号
9、signal words───信号词；标志词
1、software mainly processes the rotate speed signal of the crankshaft and camshaft position signal to export ignition control signal.───软件部分主要对曲轴速度信号、凸轮轴基准信号等进行处理计算，输出点火控制信号。
2、The duration of position persistence is such that objects visible briefly always generate a position signal for at least 180 ms.───时间持续的立场是，物体的可见简要总是生成一个位置信号，至少180毫秒。
3、This method requires detection of only the position signal, but not the speed or acceleration signals.───该方法无需测量关节速度和加速度，只需要测量关节位置信号。
4、There may be then a means for detecting the slew angle of the peel and for compensating the workpiece position signal thereby.───有可能是当时的一种手段，为侦查转换的角度，果皮和补偿工件的位置信号，从而。
5、the output port of the single chip is connected to the displaying circuit, locking, alarm and arbor position signal output circuit.───单片计算机的输出端口与显示电路，锁紧、报警及刀架工位信号输出电路连接。
6、The key problem of analysis in circular rotating information can be solved by the method of space equal-position signal collection.───的等位空间采集法解决了在周期旋转动态信息中作定位分析的关键问题，即动态信号定位问题。
7、has made experiment detection and rectification with signal control technology for the position signal error.───控制技术对位置信号误差角进行了实验检测及校正。
8、A rotor position detecting circuit is designed to obtain high-resolution rotor position signal from a low-resolution discrete Hall sensor.───通过设计一个转子位置检测电路将低分辨率的霍尔信号转换成高分辨率的转子位置信号。
9、Flower color and position signal to insects the blossom's degree of maturity.───花色和位置，向昆虫传递着花株的成熟程度。
1、In order to prevent from data fault during power failure, grating torque sensor provides absolute zero position signal with zero position grating.
2、It's for detection of engine speed, piston top dead center position, signal ignition and injection control in top dead center of each piston.
3、The software mainly processes the rotate speed signal of the crankshaft and camshaft position signal to export ignition control signal.
4、A basic way of measuring the position angle signal for synchro was introduced. In this paper digital method of position signal based on TMS320LF2407 and software design were introduced.
5、A new digitized model of position signal for a set of selsyn system is developed according to the principles of selsyn and the application environment of actual system.
6、Explanations on the loop operation principle, beam spot position signal extraction, and selection of motor control mode are presented.
7、When obtain piston position signal from Crankshaft, Top Dead Center Sensor and Crankshaft Position Sensor tend to be integrative in structure.