大家都搜：
n.（行扫描起点不一致引起屏幕上的）锯齿状；锯齿状突起（等于serrature）
1、serranus cjer───蛇
2、serrasalmus geryi───谢尔LaSa尔穆斯格伊
3、serrate verb───锯齿状动词
4、serrated edge───牙子；锯齿形边
5、chloranthus serratus───[医] 及己
6、prunus serrulata───樱桃
7、shea serrano───谢·塞拉诺
8、serrate suture───[解剖]锯状缝
9、serrate gene───锯齿基因
10、serrate leaf───锯齿叶
1、Point contact in both cylinders Small grooves are called "Serration" , each serration assign as cutting edges.───小槽被称为“锯齿”每一锯齿可看作为一个刀刃。
2、points for attention in designing the serration axle are pointed out.───指出了渐开线螺旋花键轴几何尺寸设计时应注意的问题。
3、Post processing method is put forward in order to removal serration of spectral curve after calibration.───提出了反射率反演后波谱曲线上存在的锯齿状现象的消除方法；
4、secondary veins 13-15 on each side of midvein, adaxially slightly raised, fusing at serration.───中脉凹陷次脉13-15在中脉两边各，正面稍突起，在熔化。
5、The new method for designing Fresnel lens has a wide serration breadth and unequal pitch.───用这一方法设计的菲涅耳透镜，齿宽较大，齿距不等。
6、screw driver for screws with internal serration - screw driver points , gauges and test specimens for torque testing.───螺钉和螺母的装配工具。十字头套筒扳手。尺寸和扭矩试验。
7、Serration flow phenomenon of aluminum alloy used for can body stock───易拉罐用铝材的锯齿屈服现象
8、The results show that high stress in serration and its arc transition region, and observed that severe stress concentration in these locations.───结果表明叶片高应力区域位于榫齿及其圆弧过渡处，并且发现在这些位置存在严重的应力集中情况。
9、Mechanical Analysis of Crack Failures in Turbine Blade and Disk Serration of an Aeroengine───某型航空发动机涡轮叶片和轮盘榫齿裂纹故障力学分析
1、Unless otherwise specified, the nozzle gasket surface shall be flat smooth surface and serration specified in ANSI standard is not to provide.
2、The full text used the methods of combining literature and the literature, and make serration research as a whole for Li zhi.
3、We adopt serration design in order for thermolysis and life.
4、The optimization rule on the layout and serration of the compact range was referred to, then the optimization algorithm was performed and the result was given.
5、The results show that high stress in serration and its arc transition region, and observed that severe stress concentration in these locations.
6、It is difficult to grind bore on gear and secure its precision. Especially more linkage gear's precision can not be secured easily, so it maybe become a waste product because of serration error.
7、Moreover, intergranular corrosion on the serration surface is other reason to induce GH2036 turbine disc to early fail under the high-temperature combustion condition.
8、As the rise of the strain rate, the feature of the true stress- true strain curve changed from flat to serration, and the thermal deformation softening feature was reinforced.
9、The points for attention in designing the serration axle are pointed out.