大家都搜：
[塑料]注射压力，喷注压力
1、pressure───vt.迫使；密封；使……增压；n.压力；压迫，[物]压强
2、dependency injection───依赖注入
3、injection mold───[塑料]注塑模具
4、cash injection───资金注入
5、corticosteroid injection───PiZhiLeiGuChun注射
6、amnios injection───羊膜注射
7、administering injection───注射给药
8、direct injection───直接射油，直接注入；[动力]直接PenShe；直接注入；直接射出法
9、alegar injection───阿莱加注射液
1、Cycle polymer flooding method can reduce injection pressure.───周期注聚方式可以降低注入压力。
2、Bad injected water quality have damaged formations and made injection pressure step up in Shasanzhong 6-10 low permeable reservoirs.───濮城油田沙三中6-10油藏为低渗油藏，因注入水质差，造成对地层的伤害，注水压力不断上升。
3、Theoretical result shows that even in a very low admixture injection pressure, fracturing will occur in surrounding soil.───理论分析发现即使在很小的固化剂注入压力作用下，周围土体也会发生劈裂现象。
4、In the function of injection pressure, the mould which has core will produce a little core offset and cause plastics deformation.───具有型芯的模具，在注射压力的作用下，将使型芯产生一定偏移，引起塑件变形。
5、The injection pressure is commonly described as the surface pump pressure required to achieve injection.───注入压力普遍地是指实现注入所需的地面泵压。
6、Injection pressure in one of the major factors effecting the results of development of sandstone reservoirs.───注水开发的砂岩油田，注水压力的高低对油田开发效果有很大的影响。
7、The high pertinence between the weight of injection molding products and injection pressure is unveiled by experiments and analyses.───通过实验和分析揭示了注塑机产品的件重和充填过程的压力之间有很强的相关性。
8、When the close time of the nozzles was set at the end of packing, the injection pressure, clamp force and parts quality were all better.───同时当浇口均设置为保压结束时关闭，成型中的注射压力、锁模力以及制件质量较为理想。
9、Influence of injection pressure and fuel temperature for standard fuel consumption was studied.───了喷油器开启压力和试验油温度对标准油量的影响；
1、Electric unit pump system is a new type fuel injection system with high injection pressure which can be applied to control fuel quantity and timing of injecting flexibly.
2、It is demonstrated that a flashing jet is worn away into a cone shape and the jet extinct length decreases with the increasing of pressure decay ratio of injection pressure to backpressure.
3、Therefore, using higher specific gravity and dynamic viscosity of biodiesel is able to decrease fuel injection pressure properly.
4、The sensitivity analysis indicates that the parameters impacting the production results from high to low are production time, steam dryness, cyclic steam injection volume, steam injection pressure.
5、Water injection efficiency depends on whether the injection pressure is high or low in water injection wells.
6、The molder must recognize the dangers of excessive fill speed, insufficient injection pressure, excessive melt temperature, and inadequate packing.
7、It could non-disassembly dynamic test several parameters of the fuel system, such as fuel injection pressure, fuel injection bulkhead angle, fuel injection and fuel supply advance angle.
8、During the process of water injection production, high injection pressure cut in mudstone should be prevented to reduce casing damage.
9、Due to high injection pressure of high concentration polymer solution, reducing injection pressure of high-concentration polymer solution with surfactant has been researched.